HTML datasheet archive (search documentation on electronic components) Search datasheet (1.687.043 components)
Search field

Datasheet: M150XN07 (No company)

15.0Ў± Xga Color Tft-lcd Module

 

Download: PDF   ZIP
No company
(C) Copyright AU Optronics, Inc.
Feb. 2003 All Rights Reserved. M150XN07 Ver0.1
1/28
No Reproduction and Redistribution Allowed.

AU OPTRONICS CORPORATION
Product Specifications
15.0
"
XGA Color TFT-LCD Module

Model Name: M150XN07
V.1


Approved by
Prepared by
DDBU Marketing Division / AU Optronics Croporation
Customer
Checked & Approved by




Spec. No.: DDPM-M150XN07-0.1
Version: 1
Total pages: 26
Date: 2003-July-31
(C) Copyright AU Optronics, Inc.
Feb. 2003 All Rights Reserved. M150XN07 Ver0.1
2/28
No Reproduction and Redistribution Allowed.










Product Specifications
15.0
"
XGA Color TFT-LCD Module
Model Name:M150XN07
V.1


(
u
) Preliminary Specifications
(
) Final Specifications








(C) Copyright AU Optronics, Inc.
Feb. 2003 All Rights Reserved. M150XN07 Ver0.1
3/28
No Reproduction and Redistribution Allowed.
i Contents
1.0 Handling Precautions
2.0 General Description
2.1 Display Characteristics
2.2 Functional Block Diagram
3.0 Absolute Maximum Ratings
4.0 Optical Characteristics
4.1 Signal for Lamp connector
4.2 Parameter guideline for CCFL Inverter
5.0 Signal Interface
5.1 Module Interface Connectors
5.2 Module Connector Pin Configuration
5.3 Backlight Connectors
5.4 Backlight Connector Pin Configuration
5.5 Signal Electrical Characteristics
5.6 Interface Timings Characteristics
5.7 Interface Timing Definition
6.0 Pixel format image
7.0 Power Consumption

8.0 Power ON/OFF Sequence

9.0 Backlight Characteristics
9.1 Signal for Lamp connector
9.2 Parameter guideline for CCFL Inverter
10.0Vibration, Shock, and Drop
10.1 Vibration & Shock
10.1.1 Vibration Test Spec
10.1.2 Shock Test Spec
10.2 Drop
11.0 Environment
11.1 Temperature and Humidity
11.1.1 Operating Conditions
11.1.2 Shipping Conditions
11.2 Atmospheric Pressure
11.3 Thermal Shock
12.0 Reliability
12.1 Failure criteria
12.2 Failure rate
12.2.1 Usage
12.2.2 Components de-rating
12.3 CCFL life
12.4 ON/OFF cycle

(C) Copyright AU Optronics, Inc.
Feb. 2003 All Rights Reserved. M150XN07 Ver0.1
4/28
No Reproduction and Redistribution Allowed.
13.0 Safety
13.1 Sharp edge requirement
13.2 Material
13.2.1 Toxicity
13.2.2 Flammability
13.3 Capacitors
13.4 Hazardous voltage
14.0 Other requirements
14.1 Smoke free design
14.2 National test lab requirement
15.0 Label
16.0 Mechanical Characteristics






ii Record of Revision
Version and Date Page
Old description
New Description
Remark
0.1 2003/06/10
All
First Edition for Customer
All
(C) Copyright AU Optronics, Inc.
Feb. 2003 All Rights Reserved. M150XN07 Ver0.1
5/28
No Reproduction and Redistribution Allowed.
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when
handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out from the
container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL
Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (LCD monitor housing, for example), do not twist nor
bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration
that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or
regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be
supplied by power complied with requirements of Limited Power Source (2.11, IEC60950 or UL1950), or be applied
exemption.
14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit (2.4, IEC60950 or UL1950).
Do not connect the CFL in Hazardous Voltage Circuit.











© 2018 • ICSheet
Contact form
Main page