HTML datasheet archive (search documentation on electronic components) Search datasheet (1.687.043 components)
Search field

Datasheet: CSOV3S3 (Connor-Winfield)

Oven Controlled Crystal Oscillators (40 MHz to 80 MHz, 0 to 70c)

 

Download: PDF   ZIP
 
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
The Connor-Winfield
CGOV3S3 is a hermetically
sealed 14 Pin DIP, 3.3V Oven
Controlled Voltage Controlled
Crystal Oscillator (OCVCXO)
HCMOS/TTL Compatible.
The CGOV3S3 is designed
for a higher stability Stratum 3
application requiring low jitter
and tight stability.
1
2
CGOV3S3 - 33.333333MHz
OCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
3.3V OPERATION
LOW JITTER <3pS RMS
FREQUENCY STABILITY: 0.25ppm
TEMPERATURE RANGE: 0 to 70C
FREQUENCY TOLERANCE OF 3.0ppm
OVER TEN YEARS
14 PIN DIP 3.3V STRATUM 3 HCMOS OCVCXO


Cx038
00
9/23/02
www.conwin.com
CGOV3S3
CW 0107
CGOV3S3
33.333333M
Notes:
1) Initial calibration @ 25
C, Vc=1.4V.
2) Frequency stability, 0 to 70
C, referenced to 25C.
3) Frequency stability per 5% change in supply voltage.
4) At the time of shipment after 48 hours of operation.
5) Inclusive of operating temperature range, supply voltage change, load change, shock and
vibration, 10 years aging, Vc=1.4V.
6) Measured @ 25
C, within 5 minutes, the unit will be within +/-0.1ppm of its reference frequency,
measured after 30 minutes of continuous operation at a stable 25
C
7) Referenced to Fo @ 25
C, Positive Transfer Characteristic.



ABSOLUTE MAXIMUM RATINGS
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Storage Temperature
-40
-
85
C
Supply Voltage
(Vcc)
-0.5
-
4.5
Vdc
Control Voltage
(Vc)
-0.5
-
4.5
Vdc
OPERATING SPECIFICATIONS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Center Frequency
(Fo)
1.544
-
38.88
MHz
Frequency Calibration
-1.5
1.5
ppm
1, 4
Frequency vs. change in Temperature
-0.25
-
0.25
ppm
2
Frequency vs. change in Supply Voltage
-0.05
-
0.05
ppm
3
Aging (Daily)
-30
-
30
ppb
4
Aging (10 Years)
-2.5
-
2.5
ppm
Total Frequency Tolerance
-3.0
-
3.0
ppm
5
Operating Temperature Range
0
-
70
C
Supply Voltage
(Vcc)
3.135
3.300
3.465
Vdc
Supply Current
(Icc)
-
-
400
mA
Jitter (BW=10Hz to 20MHz)
-
-
3
ps rms
Allan Variance (1 second)
-
5.00E-10
-
SSB Phase Noise at 10Hz offset
-
-90
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-130
-
dBc/Hz
Start Up Time: Oscillator
-
-
10
mS
Warm Up Time
-
-
5
Minutes
6
TDEV @ 1.0 Sec.
-
-
1
nS
TDEV @ 4.0 Sec.
-
-
2
nS
INTPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Control Voltage Range
(Vc)
0.3
1.4
3.0
Vdc
Frequency at Vc=0.3 Vdc
-
-7
-5
ppm
7
Frequency at Vc=3.0 Vdc
5
7
-
ppm
7
Slope of Frequency Adjust
2.8
-
-
ppm/V
Input Impedance
100k
-
-
Ohm
HCMOS OUTPUT
CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
LOAD
12
15
18
pf
Voltage (High)
(Voh)
2.6
-
-
Vdc
(Low)
(Vol)
-
-
0.4
Vdc
Current (High)
(Ioh)
-4
-
mA
(Low)
(Ioh)
-
-
4
mA
Duty Cycle at 50% of Vcc
45
50
55
%
Rise / Fall Time 10% to 90%
-
-
6
nS
PACKAGE
CHARACTERISTICS
TABLE 5.0
Package
14 pin DIP, hermetically sealed, grounded case, welded package
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
2
2
Cx038
00
9/23/02
www.conwin.com
ENVIRONMENTAL CHARACTERISTICS
Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55C to 125C, 20 cycles,10 minute dwell, 1m inute
transition.
Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No bubbles in flourinert (FC-43) at 125C 5C for 20
seconds.

SOLDERING
Pin Solderability: Per MIL-STD-883, Method 200. 8 hour steam age prior to 254C 5C Solder pot dip, 95% Coverage.
Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board -mount product, 260C
5C for 20 Seconds.

MECHANICAL CHARACTERISTICS
Vibration: Per MIL-STD-202, Method 204, Condition A. 10G's peak, 10Hz to 500Hz, 15mi nute cycles 12 times each
perpendicular axis.
Shock: Per MIL-STD-202, Method 213, Condition D. 500G's, 1ms, half sine, 3 shocks per direction.
Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65C, 10 cycles 10C to 65C.
CONTROL VOLTAGE
CONTROL
VOLTAGE
+3.3Vdc
© 2018 • ICSheet
Contact form
Main page