HTML datasheet archive (search documentation on electronic components) Search datasheet (1.687.043 components)
Search field

Datasheet: ASOV5S3 (Connor-Winfield)

Oven Controlled Crystal Oscillators (1.544 MHz to 20 MHz, 0 to 70c)

 

Download: PDF   ZIP
 
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
The Connor-Winfield
AGOV5S3 is a hermetically
sealed 14 Pin DIP 5.0V Oven
Controlled Crystal Oscillator
(OCXO) with an HCMOS
output. The AGOV5S3 is
designed for Stratum 3
applications requiring low
jitter and tight frequency
stability.
1
2
AGOV5S3 - 12.800MHz
OCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
FREQUENCY ADJUST
5.0V OPERATION
LOW JITTER <1pS RMS
TEMPERATURE STABILITY
0.25ppm
TEMPERATURE RANGE: 0 to 70C
FREQUENCY TOLERANCE OF
4.6ppm OVER TWENTY YEARS
LOW PROFILE 14 PIN DIL PACKAGE
14 PIN DIP 5.0V HCMOS STRATUM 3 OCXO


Cx015
01
6/25/03
www.conwin.com
AGOV5S3
CW 0107
AGOV5S3
12.800M
ABSOLUTE MAXIMUM RATINGS
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Storage Temperature
-40
-
85
C
Supply Voltage
(Vcc)
-0.5
-
7.0
Vdc
Control Voltage
(Vc)
-0.5
-
7.0
Vdc
OPERATING SPECIFICATIONS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Center Frequency, Vc=2.18 Vdc
(Fo)
1.544
-
20.0
MHz
Frequency Calibration
-1.5
1.5
ppm
1
Frequency Stability
-0.25
-
0.25
ppm
2
Aging (Daily)
-30
-
30
ppb
3
Aging (20 Years)
-2.5
-
2.5
ppm
Total Frequency Tolerance
-4.6
-
4.6
ppm
4
Operating Temperature Range
0
-
70
C
Supply Voltage
(Vcc)
4.75
5.0
5.25
Vdc
Supply Current
(Icc)
-
-
300
mA
Phase Jitter (BW=12KHz to 20MHz )
-
-
1
ps rms
Phase Jitter (BW=10Hz to 20MHz)
-
-
3
ps rms
Period Jitter
-
-
3
ps rms
SSB Phase Noise at 10Hz offset
-
-90
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-135
-
dBc/Hz
Start Up Time: Oscillator
-
-
10
mS
Warm Up Time
-
-
5
Minutes
5
TDEV @ 1.0 Sec.
-
-
1
nS
TDEV @ 4.0 Sec.
-
-
2
nS
INTPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Control Voltage Range
(Vc)
0.5
2.18
4.1
Vdc
Frequency at Vc=0.5 Vdc
-30
-
-18
ppm
6
Frequency at Vc=4.1 Vdc
18
-
30
ppm
6
Slope of Frequency Adjust
5
-
-
ppm/V
Input Impedance
100k
-
-
Ohm
HCMOS OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
LOAD
-
-
15
pf
Voltage (High)
(Voh)
4.5
-
-
Vdc
(Low)
(Vol)
-
-
0.4
Vdc
Current (High)
(Ioh)
-4
-
mA
(Low)
(Ioh)
-
-
4
mA
Duty Cycle at 50% of Vcc
45
50
55
%
Rise / Fall Time 10% to 90%
-
-
6
nS
PACKAGE CHARACTERISTICS
TABLE 5.0
Package
14 pin DIP, hermetically sealed, grounded case, welded package

Notes:
1) Initial calibration @ 25
C, Vc=2.18 Vdc.
2) Frequency vs. temperature stability
3) At the time of shipment after48 hours of operation.
4) Inclusive of calibration, operating temperature range, supply voltage change, load change, shock
and vibration, 20 years aging, Vc=2.18 Vdc.
5) Measured @ 25
C, within 5 minutes, the unit will be within +/-0.1ppm of its reference frequency,
measured after 30 minutes of continuous operation at a stable 25
C
6) Referenced to Fo @ 25
C
, Positive Transfer Characteristic

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
2
2
Cx015
01
6/25/03
www.conwin.com
ENVIRONMENTAL CHARACTERISTICS
Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55C to 125C, 20 cycles,10 minute dwell, 1m inute
transition.
Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No bubbles in flourinert (FC-43) at 125C 5C for 20
seconds.

SOLDERING
Pin Solderability: Per MIL-STD-883, Method 200. 8 hour steam age prior to 254C 5C Solder pot dip, 95% Coverage.
Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board -mount product, 260C
5C for 20 Seconds.

MECHANICAL CHARACTERISTICS
Vibration: Per MIL-STD-202, Method 204, Condition A. 10G's peak, 10Hz to 500Hz, 15mi nute cycles 12 times each
perpendicular axis.
Shock: Per MIL-STD-202, Method 213, Condition D. 500G's, 1ms, half sine, 3 shocks per direction.
Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65C, 10 cycles 10C to 65C.
CONTROL VOLTAGE
1
7
8
14
4.1Vdc
5.0Vdc
TEST DIAGRAM
© 2018 • ICSheet
Contact form
Main page